DTC P0366 (1.5 L Engine)
DTC P0366 : CMP Sensor B and CKP Sensor Incorrect Phase Detected
NOTE:
- Before you troubleshoot, review the general troubleshooting information .
- If the DTC P101A stored at the same time as DTC P0366, troubleshoot DTC P101A first, then recheck for DTC P0366.
| DTC Description | Confirmed DTC | Pending DTC |
|---|---|---|
| P0366 CMP Sensor B and CKP Sensor Incorrect Phase Detected |
DTC (PGM-FI)
- Problem verification
-1. Turn the vehicle to the ON mode.
-2. Clear the DTC with the HDS.
-3. Turn the vehicle to the OFF (LOCK) mode, and allow the engine to cool below 104 deg. F (40 deg. C).
-4. Start the engine, and let it idle without load (CVT in P or N, M/T in neutral).
-5. Check for Pending or Confirmed DTCs with the HDS.
DTC Description Confirmed DTC Pending DTC P0366 CMP Sensor B and CKP Sensor Incorrect Phase Detected Is DTC P0366 indicated?
YES
Go to step 5.
NO
Go to step 2.
- VTC system check (VTC TEST with the HDS)
-1. Select the VTC TEST in the Function Test with the HDS, then select the EX-VTC.
VTC TEST - EX-VTC
Is the result OK?
YES
Go to step 3.
NO
Go to step 5.
- VTC system check (EX VTC Status check with the HDS)
-1. Test-drive the vehicle at a steady speed between 19-38 mph (30-60 km/h) for 10 minutes.
-2. Check the parameter (s) below with the HDS.
Signal Threshold Current conditions Values Unit Values Unit EX VTC Status ON Do the current condition (s) match the threshold?
YES
Go to step 4.
NO
Do the test-drive again, then recheck the EX VTC Status.
- VTC system check (OBD STATUS check)
-1. Monitor the OBD STATUS for DTC P0366 in the DTCs MENU with the HDS.
DTC Description OBD STATUS P0366 CMP Sensor B and CKP Sensor Incorrect Phase Detected Does the HDS indicate FAILED?
YES
Go to step 5.
NO
If the HDS indicates PASSED, intermittent failure, the system is OK at this time. If the on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the on-board snapshot . If the HDS indicates NOT COMPLETED, go to step 3, and recheck.
- VTC oil control solenoid valve B operation check
-1. Test VTC oil control solenoid valve B .
Is the solenoid valve OK?
YES
Go to step 6.
NO
- Camshaft timing check
-1. Check the camshaft timing .
Is the camshaft timing OK?
YES
Go to step 7.
NO
- Cam chain check
-1. Check for damage or stretch at the cam chain .
Is the cam chain damaged or stretched?
YES
Replace the cam chain and the auto-tensioner .
NO
Go to step 8.
- VTC actuator B check
-1. Inspect VTC actuator B .
Is the actuator OK?
YES
Go to step 9.
NO
- PGM-FI system check (DTC check)
-1. Turn the vehicle to the ON mode.
-2. Reset the PCM with the HDS .
Reset PCM
-3. Do the CKP pattern clear procedure .
CRANK (CKP) PATTERN CLEAR
-4. Do the PCM idle learn procedure .
-5. Do the CKP pattern learn procedure .
CRANK (CKP) PATTERN LEARNING
-6. Turn the vehicle to the OFF (LOCK) mode, and allow the engine to cool below 104 deg. F (40 deg. C).
-7. Start the engine, and let it idle without load (CVT in P or N, M/T in neutral).
-8. Check for Pending or Confirmed DTCs with the HDS.
DTC Description Confirmed DTC Pending DTC P0366 CMP Sensor B and CKP Sensor Incorrect Phase Detected Is DTC P0366 indicated?
YES
Check for poor connections or loose terminals at VTC oil control solenoid valve B and the PCM, then go to step 1.
NO
Intermittent failure, the system is OK at this time. If the on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the on-board snapshot .