LEMON Manuals: Even more car manuals for everyone
Home >> Acura >> 2012 >> TL SH-AWD, Standard Trans >> Repair and Diagnosis >> Drivelines & Axles >> Axle Shafts >> Driveline/Axle >> Front Driveshaft Installation

Front Driveshaft Installation

NOTE: Before starting installation, make sure the mating surfaces of the joint and the splined section are clean.
  1. Apply about 5 g (0.18 oz) of moly 60 paste (P/N 08734-0001) to the contact area (A) of the outboard joint and the front wheel bearing.
    NOTE: The paste helps prevent noise and vibration.
    Fig 1: Identifying Contact Area Of Outboard Joint
    G08070062Courtesy of AMERICAN HONDA MOTOR CO., INC.
  2. Install a new set ring (A) into the set ring groove (B) of the left driveshaft inboard joint.
    Fig 2: Identifying Set Ring And Set Ring Groove
    G08070063Courtesy of AMERICAN HONDA MOTOR CO., INC.
  3. Install a new set ring (A) into the set ring groove (B) of the intermediate shaft.
    Fig 3: Identifying Set Ring And Set Ring Groove
    G08070064Courtesy of AMERICAN HONDA MOTOR CO., INC.
  4. Apply specified quantity of super high temp urea grease (P/N 08798-9002) to the whole splined surface (A) of the right driveshaft. After applying grease, remove the grease from the splined grooves at intervals of 2- 3 splines and from the set ring groove (B) so that air can bleed from the intermediate shaft.
    Fig 4: Applying Super High Temp Urea Grease To Whole Splined Surface Of Right Driveshaft
    G08070065Courtesy of AMERICAN HONDA MOTOR CO., INC.
    Model Grease quantity
    M/T 2.0- 3.0 g (0.07- 0.11 oz)
    A/T 0.5- 1.0 g (0.02- 0.04 oz)
  5. Clean the areas where the driveshaft contacts the differential thoroughly with solvent, and dry them with compressed air.
    NOTE: Do not wash the rubber parts with solvent.
  6. Insert the inboard end (A) of the driveshaft into the differential (B) or the intermediate shaft (C) until the set ring (D) locks in the groove (E).
    NOTE: Insert the driveshaft horizontally to prevent damaging the oil seal.
    Fig 5: Inserting Inboard End Of Driveshaft Into Differential Shaft Until Set Ring Locks In Groove - Left
    G08070066Courtesy of AMERICAN HONDA MOTOR CO., INC.
    Fig 6: Inserting Inboard End Of Driveshaft Into Differential Shaft Until Set Ring Locks In Groove - Right
    G08070067Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Install the outboard joint (A) into the front hub on the knuckle.
    Fig 7: Installing Outboard Joint Into Front Hub On Knuckle
    G08070068Courtesy of AMERICAN HONDA MOTOR CO., INC.
  8. Install exhaust pipe A.
  9. Wipe off any grease contamination from the ball joint tapered section and threads, then install the knuckle (A) onto the lower arm (B). Be careful not to damage the ball joint boot (C). Wipe off the grease before tightening the nut at the ball joint. Torque a new castle nut (D) to the lower torque specification, then tighten it only far enough to align the slot with the ball joint pin hole.
    NOTE:
    • Make sure the ball joint boot is not damaged or cracked.
    • Do not align the nut by loosening it.
    Fig 8: Knuckle, Cotter Pin, Lower Arm, Ball Joint Boot And Nut With Torque Specifications
    G08070069Courtesy of AMERICAN HONDA MOTOR CO., INC.
  10. Install a new cotter pin (E) into the ball joint pin hole, and bend the cotter pin as shown.
  11. Install the damper fork (A) over the driveshaft and onto the lower arm. Install the damper in the damper fork so the aligning tab (B) is aligned with the slot in the damper fork. Loosely install the damper pinch bolt (C).
    Fig 9: Damper Fork, Aligning Tab, Flange Bolt, Pinch Bolt And Damper Fork Mounting Nut With Torque Specifications
    G08070070Courtesy of AMERICAN HONDA MOTOR CO., INC.
  12. Loosely install a new flange bolt (D) and a new damper fork mounting nut (E).
  13. Connect the front stabilizer link (A) to the lower arm, and loosely install the flange nut (B). Hold the stabilizer joint pin (C) using a hex wrench (D), and tighten the flange nut.
    Fig 10: Front Stabilizer Link, Hex Wrench, Stabilizer Joint Pin And Flange Nut With Torque Specifications
    G08070071Courtesy of AMERICAN HONDA MOTOR CO., INC.
  14. Place a floor jack under the lower arm, and raise the suspension to load it with the vehicle's weight.
    NOTE: Do not put the floor jack under the ball joint.
  15. Tighten the damper pinch bolt and the damper fork mounting nut while holding the flange bolt to the specified torque values, then remove the floor jack.
  16. Apply a small amount of engine oil to the seating surface of a new spindle nut (A).
    Fig 11: Spindle Nut Shoulder And Spindle Nut With Torque Specifications
    G08070072Courtesy of AMERICAN HONDA MOTOR CO., INC.
  17. Install the spindle nut, then tighten it. After tightening, use a drift to stake the spindle nut shoulder (B) against the driveshaft.
  18. Clean the mating surfaces between the brake disc and the inside of the wheel, then install the front wheel.
  19. Turn the wheel by hand, and make sure there is no interference between the driveshaft and surrounding parts.
  20. Lower the vehicle.
  21. Refill the transmission with recommended transmission fluid:
  22. Check the wheel alignment, and adjust it if necessary (see WHEEL ALIGNMENT ).
  23. Test-drive the vehicle.
scientia non olet · About LEMON Manuals