DTC Troubleshooting

DTC Troubleshooting: P0848 (26)

DTC P0848: Open in 3rd Clutch Transmission Fluid Pressure Switch Circuit, or 3rd Clutch Transmission Fluid Pressure Switch Stuck OFF

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information. How to Troubleshoot A/T Systems

1. Clear the DTC with the HDS.

2. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).

3. Drive the vehicle in 3rd gear in M, and check with the HDS in the A/T data list that the Shift Control indicates 3rd.

4. Check the 3rd Pressure Switch signal with the HDS in the A/T data list.

Is the 3rd Pressure Switch ON?
YES - Go to step 5.

NO - Go to step 7.


5. Drive the vehicle in 3rd gear in M for at least 2 seconds.

6. Monitor the OBD STATUS for P0848 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate FAILED?
YES - Go to step 7.

NO - If the HDS indicates PASSED, intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the 3rd clutch transmission fluid pressure switch and the PCM. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.


7. Turn the ignition switch to LOCK (0).

8. Disconnect the 3rd clutch transmission fluid pressure switch connector.

9. Turn the ignition switch to ON (II).

10. Measure the voltage between the 3rd clutch transmission fluid pressure switch connector terminal and body ground.

Is there about 5 V?
YES - Replace the 3rd clutch transmission fluid pressure switch, 3rd Clutch Transmission Fluid Pressure Switch Replacement then go to step 20.

NO - Go to step 11.






11. Turn the ignition switch to LOCK (0).

12. Jump the SCS line with the HDS.

13. Disconnect PCM connector C (49P).

14. Check for continuity between PCM connector terminal C38 and the 3rd clutch transmission fluid pressure switch connector terminal.

Is there continuity?
YES - Check for poor connections and loose terminals at the 3rd clutch transmission fluid pressure switch and the PCM. If the connections are OK, go to step 15.

NO - Repair open in the wire between PCM connector terminal C38 and the 3rd clutch transmission fluid pressure switch, then go to step 20.






15. Reconnect all connectors.

16. Update the A/T software in the PCM if it does not have the latest software, Service and Repair or substitute a known-good PCM. How to Troubleshoot A/T Systems

17. Drive the vehicle in 3rd gear in M for at least 2 seconds, then upshift to 4th gear, and drive for at least 2 seconds. Slow down and stop the wheels.

18. Check for Temporary DTCs or DTCs with the HDS.

Is DTC P0848 indicated?
YES - If the PCM was updated, substitute a known-good PCM, How to Troubleshoot A/T Systems then recheck. If the PCM was substituted, go to step 1.

NO - Go to step 19.


19. Monitor the OBD STATUS for P0848 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate PASSED?
YES - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM. Service and Repair If any other DTCs were indicated on step 18, go to the indicated DTC's troubleshooting.

NO - If the HDS indicates FAILED, check for poor connections and loose terminals at the 3rd clutch transmission fluid pressure switch and the PCM. If the PCM was updated, substitute a known-good PCM, How to Troubleshoot A/T Systems then recheck. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, return to step 17 and recheck.


20. Clear the DTC with the HDS.

21. Drive the vehicle in 3rd gear in M for at least 2 seconds, then upshift to 4th gear and drive for at least 2 seconds. Slow down and stop the wheels.

22. Check for Temporary DTCs or DTCs with the HDS.

Is DTC P0848 indicated?
YES - Check for poor connections and loose terminals at the 3rd clutch transmission fluid pressure switch and the PCM, then go to step 1.

NO - Go to step 23.


23. Monitor the OBD STATUS for P0848 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

Does the HDS indicate PASSED?
YES - Troubleshooting is complete. If any other DTCs were indicated on step 22, go to the indicated DTC's troubleshooting.

NO - If the HDS indicates FAILED, check for poor connections and loose terminals at the 3rd clutch transmission fluid pressure switch and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, return to step 21 and recheck.