LEMON Manuals: Even more car manuals for everyone
Home >> Acura >> 2007 >> TL Base >> Repair and Diagnosis >> Engine Performance >> System >> PGM-FI System >> DTC Troubleshooting >> DTC P2270: Rear Secondary HO2S (Bank 1, Sensor 2) Circuit Signal Stuck Lean; DTC P2271: Rear Secondary HO2S (Bank 1, Sensor 2) Circuit Signal Stuck Rich; DTC P2272: Front Secondary HO2S (Bank 2, Sensor 2) Circuit Signal Stuck Lean; DTC P2273: Front Secondary HO2S (Bank 2, Sensor 2) Circuit Signal Stuck Rich

DTC P2270: Rear Secondary HO2S (Bank 1, Sensor 2) Circuit Signal Stuck Lean; DTC P2271: Rear Secondary HO2S (Bank 1, Sensor 2) Circuit Signal Stuck Rich; DTC P2272: Front Secondary HO2S (Bank 2, Sensor 2) Circuit Signal Stuck Lean; DTC P2273: Front Secondary HO2S (Bank 2, Sensor 2) Circuit Signal Stuck Rich

NOTE:
  • Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
  • Information marked with an asterisk (*) applies to the front bank (Bank 2).
  1. Turn the ignition switch ON (II).
  2. Clear the DTC with the HDS.
  3. Start the engine, and let it idle without load (in Park or neutral) until the radiator fan comes on.
  4. Test-drive under these conditions:
    • Engine coolant temperature (ECT SENSOR 1) above 158 °F (70 °C)
    • Vehicle speed at 35 mph (56 km/h) or more for at least 40 seconds
  5. Monitor the OBD STATUS for DTC P2270, P2271, P2272*, and/or P2273* in the DTCs MENU with the HDS.

    Does the screen indicate FAILED? 

    YES  -Go to step 6.

    NO  -If the screen indicates PASSED, intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM/PCM. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, go to step  3 and recheck.

  6. Turn the ignition switch OFF.
  7. Replace the secondary HO2S (Sensor 2) (see SECONDARY HO2S REPLACEMENT  ).
  8. Turn the ignition switch ON (II).
  9. Reset the ECM/PCM with the HDS.
  10. Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
  11. Start the engine, and let it idle without load (in Park or neutral) until the radiator fan comes on.
  12. Test-drive under these conditions:
    • Engine coolant temperature (ECT SENSOR 1) above 158 °F (70 °C)
    • Vehicle speed at 35 mph (56 km/h) or more for at least 40 seconds
  13. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P2270, P2271, P2272*, and/or P2273* indicated? 

    YES  -Check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM/PCM, then go to step  1.

    NO  -Go to step 14.

  14. Monitor the OBD STATUS for DTC P2270, P2271, P2272*, and/or P2273* in the DTCs MENU with the HDS.

    Does the screen indicate PASSED? 

    YES  -Troubleshooting is complete. If any other Temporary DTCs or DTCs were indicated in step  13, go to the indicated DTCs troubleshooting.

    NO  -If the screen indicates FAILED, check for poor connections or loose terminals at the secondary HO2S (Sensor 2) and the ECM/PCM, then go to step  1. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, go to step  11.

scientia non olet · About LEMON Manuals