SAE J1979 Mode $06 Information by Test ID: Thermostat
DTC P0128, P1486: Test ID $4D: Component ID $80
| Test ID | $4D | Test Limit Type and Component ID | $80 |
| DTC | P0128, P1486 | ||
| Test Description | Check of thermostat by monitoring the time interval until ECT sensor signal reaches target value. | ||
| Store Timing | Normal judgement | ||
| Conversion to Engineering Units | Measured value: Output value - 48 (°C) The lowest limit value: Output value - 48 (°C) The highest limit value: Not applicable |
||
DTC P0128, P1486: Test ID $4E: Component ID $80
| Test ID | $4E | Test Limit Type and Component ID | $80 |
| DTC | P0128, P1486 | ||
| Test Description | Check of thermostat by monitoring the difference between actual ECT and predicted ECT. | ||
| Store Timing | Normal judgement | ||
| Conversion to Engineering Units | Measured value: Output value - 48 (°C) The lowest limit value: Output value - 48 (°C) The highest limit value: Not applicable |
||
DTC P0128, P1486: Test ID $4F: Component ID $80
| Test ID | $4F | Test Limit Type and Component ID | $80 |
| DTC | P0128, P1486 | ||
| Test Description | Check of thermostat by monitoring the time interval until ECT sensor signal reaches target value. | ||
| Store Timing | Failure judgement | ||
| Conversion to Engineering Units | Measured value: Output value - 48 (°C) The lowest limit value: Output value - 48 (°C) The highest limit value: Not applicable |
||
DTC P0128, P1486: Test ID $50: Component ID $00
| Test ID | $50 | Test Limit Type and Component ID | $00 |
| DTC | P0128, P1486 | ||
| Test Description | Check of thermostat by monitoring the difference between actual ECT and predicted ECT. | ||
| Store Timing | Failure judgement | ||
| Conversion to Engineering Units | Measured value: Output value x 1 (°C) The lowest limit value: Not applicable The highest limit value: Output value x 1 (°C) |
||
DTC P0128: Test ID $4D: Component ID $81
| Test ID | $4D | Test Limit Type and Component ID | $81 |
| DTC | P0128 | ||
| Test Description | Check of thermostat by monitoring the time interval until ECT sensor signal reaches target value. | ||
| Store Timing | Normal judgement | ||
| Conversion to Engineering Units | Measured value: Output value (Decimal) - 40 (°C) The lowest limit value: Output value (Decimal) - 40 (°C) The highest limit value: Not applicable |
||
DTC P0128: Test ID $4E: Component ID $81
| Test ID | $4E | Test Limit Type and Component ID | $81 |
| DTC | P0128 | ||
| Test Description | Check of thermostat by monitoring the difference between actual ECT and predicted ECT. | ||
| Store Timing | Normal judgement | ||
| Conversion to Engineering Units | Measured value: Output value (Decimal) - 40 (°C) The lowest limit value: Output value (Decimal) - 40 (°C) The highest limit value: Not applicable |
||
DTC P0128: Test ID $4F: Component ID $81
| Test ID | $4F | Test Limit Type and Component ID | $81 |
| DTC | P0128 | ||
| Test Description | Check of thermostat by monitoring the difference between actual ECT and predicted ECT. | ||
| Store Timing | Failure judgement | ||
| Conversion to Engineering Units | Measured value: Output value (Decimal) - 40 (°C) The lowest limit value: Output value (Decimal) - 40 (°C) The highest limit value: Not applicable |
||
DTC P0128: Test ID $50: Component ID $01
| Test ID | $50 | Test Limit Type and Component ID | $01 |
| DTC | P0128 | ||
| Test Description | Check of thermostat by monitoring the difference between actual ECT and predicted ECT. | ||
| Store Timing | Failure judgement | ||
| Conversion to Engineering Units | Measured value: Output value (Decimal) x 1 (°C) The lowest limit value: Not applicable The highest limit value: Output value (Decimal) x 1 (°C) |
||